Thermal stability and electrical properties of XFe2O4 (X = Co,Cu,Fe,Mg,Mn Ni) high-entropy spinel ferrites prepared by reactive flash sintering

This study investigates the high-temperature stability and phase composition of two high-entropy oxides (HEOs), (Mn0.2Co0.2Ni0.2Cu0.2Fe0.2)Fe2O4 and (Mn0.2Co0.2Ni0.2Cu0.2Mg0.2)Fe2O4, prepared as single-phase samples using the reactive flash sintering technique. Results show that the annealing temperature in a nitrogen atmosphere has a significant impact on the stability of the compounds. The destabilization of the spinel structure occurs in…

Fine-grained BCZT piezoelectric ceramics by combining high-energy mechanochemical synthesis and hot-press sintering

Different stoichiometries of lead-free BaZr0.2Ti0.8O3-Ba0.7Ca0.3TiO3 (BCZT) prepared by mechanosynthesis and sintered by either conventional sintering (CS) or hot pressing (HP) techniques were studied to establish the dependence of piezoelectric and dielectric properties on sintering parameters and microstructure. All synthesized stoichiometries showed a pseudocubic perovskite phase with homogeneously distributed A- and B-cations in the structure. The…

Lanthanide vanadate-based nanoparticles as multimodal T1 -T2 MRI contrast agent and NIR luminescent imaging probe

We report the development of a multimodal lanthanide vanadate system suitable as dual T1-T2 MRI contrast agent as well as a luminescent imaging probe in the near-infrared region, using Dy3+ and Gd3+ as T2 and T1 components, respectively, and Nd3+ as the luminescent center. The vanadate matrix was chosen to avoid the undesired solubility associated to previously reported fluoride-based contrast agents.…

Ti6Al4V coatings on titanium samples by sputtering techniques: Microstructural and mechanical characterization

Although titanium is widely used as biomaterial, the control of the interface properties between its surface and the surrounding physiological environment (like bone, other tissues or biofluids) results crucial to achieve a successful osseointegration and good biomechanical and functional performance. In this work, commercially pure titanium (Grade IV) discs obtained by conventional powder metallurgy were…

Reversibility and thermal dependence of the martensitic transformation in a melt-spun Ni55Fe17Ga26Co2 Heusler alloy

An almost single phase 14 M modulated martensite is obtained in melt spun ribbon of Ni55Fe17Ga26Co2 Heusler alloy. The effect of thermal treatments on the stability of the reverse martensitic transformation from 14 M modulated martensite to austenite phase in this system has been investigated by both non -isothermal and isothermal treatments. Heating above martensitic…

Exploring the local environment of the engineered nanoclay Mica-4 under hydrothermal conditions using Eu(3+)as a luminescent probe

High charge mica Na4Al4Si4Mg6O20F4 , Mica-4, is a promising candidate as a filling material to immobilize high-level radioactive waste in deep geological repositories due to its extraordinary adsorption capacity. In contrast to traditional clay materials, the structural composition of this mica, with a high content of alu-minum in the tetrahedral sheet, enhances its chemical reactivity,…

Exploring the local environment of the engineered nanoclay Mica-4 under hydrothermal conditions using Eu(3+)as a luminescent probe

High charge mica Na4Al4Si4Mg6O20F4 , Mica-4, is a promising candidate as a filling material to immobilize high-level radioactive waste in deep geological repositories due to its extraordinary adsorption capacity. In contrast to traditional clay materials, the structural composition of this mica, with a high content of alu-minum in the tetrahedral sheet, enhances its chemical reactivity,…

Effect of sintering under CO+N-2/H-2 and CO2+air atmospheres on the physicochemical features of a commercial nano-YSZ

Given the need to process anodes and composites based on nano-YSZ in reducing or in air containing additional CO2 atmospheres for the fabrication of solid oxide fuel cells (SOFCs), and solid oxide electrolysis cells (SOECs), we have studied the effect of the exposure to CO+N2/H2 or CO2+air mixtures during sintering of YSZ green pellets, prepared from commercial nanopowders,…

Features of coupled AgBr/WO3 materials as potential photocatalysts

AgBr/WO3 composite photocatalysts with different selected molar AgBr/WO3 ratios were prepared and widely characterized by XRD, N2-adsorption, SEM, TEM, UV–visible/DRS and XPS techniques. The samples were tested using rhodamine B (RhB) or caffeine, under two illumination conditions (UV and visible light). Although AgBr and WO3 pristine materials have relatively low band gap values (2.6 eV and 2.8 eV, respectively), they…